• Please contact if you have any questions: +86-21-58386256
  • Opening Hour: Monday – Friday : 9am – 5pm

compressive strength of concrete pavers mm thick

Report No: CU:20-23489-M3 Masonry Test Report - MM …

Compression of Concrete Interlocking Paving Units ASTM C 140 Specimen ID Date Tested Width (in) Thickness (in) Length (in) Avg Cap Thickness (in) Aspect Ratio Aspect Ratio Factor Maximum Load (lbf) Area (in²) Compressive Strength (psi) 20-23170-34 10-06-20 3.970 2.420 7.900 0.054 0.610 1.00 273710 31.4 8730

Report No: CU:20-23489-M1 Masonry Test Report - MM …

Sep 17, 2020· Compression of Concrete Interlocking Paving Unit Coupons ASTM C 140 Specimen ID Date Tested Width (in) Thickness (in) Length (in) Avg Cap Thickness (in) Aspect Ratio Aspect Ratio Factor Maximum Load (lbf) Area (in²) Compressive Strength (psi) 20-23172-24 10-06-20 3.620 2.320 5.510 0.080 0.641 1.03 150450 19.9 7770

Tech Spec 2 - Basalite

Concrete pavers made in Canada are required to meet re-quirements set forth by the Canadian Standards Association CSA-A231.2 Precast Concrete Pavers. This standard requires a minimum average cube compressive strength of 7,250 psi (50 MPa) or 5,800 psi (40 MPa) at delivery. There should be no greater than 500 g/m 2 of material lost after 50 ...

SECTION 1 PERMEABLE INTERLOCKING CONCRETE PAVEMENT

Note: When 3 1/8 in. thick pavers are specified, their compressive strength test results per ASTM C 140 should be adjusted by multiplying by 1.18 to equate the results to that from 2 3/8 in. (60 mm) thick pavers. 2.02 PRODUCT SUBSTITUTIONS A. …

COMPRESSIVE STRENGTH OF CONCRETE - HARDENED …

Testing – Loading Rate for 150 mm cube (140kg/cm 2/min or 5.25 N/Sec +/- 5%) Compressive Strength of Concrete . Interpretation of Test Results ... Compressive Strength of Concrete fck actual - Based on actual cube results 08.12.09 M25+ …

Strength Evaluation of Pre-Cast Concrete Paver Block ...

Compressive Strength Test: - The Zigzag shape test specimens of size 245× 120× 60 mm were prepared for testing the compressive strength concrete. In compression testing machine there was a separate arrangement for testing the concrete paver block, which was equipped with two steel bearing blocks for holding the specimen. Alternatively, 4 mm thick

Everything You Need to Know About Concrete Strength | Cor-Tuf

Mar 31, 2019· While traditional concrete normally has a compressive strength ranging anywhere from 2,500 to 5,000 psi, UHPC can have a compressive strength of up to 10 times that of traditional concrete. After just 14 days of curing, UHPC has a compressive strength of 20,000 psi. This number increases to 30,000 psi when fully cured for 28 days.

Basics of Concrete Pavement Thickness Design

AASHO Road Test Performance Surviving Sections Loop 3 1.0 2.0 3.0 4.0 5.0 0 250 500 750 1000 1250 Serviceability Concrete (36 Sect) Asphalt (4 Sect) Loop 4 1.0 2.0 3.0 4.0 5.0 0 250 500 750 1000 1250 Load Applications

ARCHITECTURAL PAVING STONE - Concrete Products & …

A. Deliver concrete pavers to site in steel banded, plastic banded, or plastic wrapped cubes on wooden pallets ... Compressive Strength: Average compressive strength of 55 MPa (8,500 psi) with no individual unit under 50 MPa. ... in uniform layers not exceeding 150 mm (6 in.) thickness. Recommended base surface tolerance should be plus or minus ...

CONCRETE PAVERS National Distribution 888-380-5575 …

6. Weight: 11 to 22 lbs per square foot depending on paver size & thickness. D. Concrete Pavers: Recycled-Glass Series pavers as manufactured by Tile Tech Pavers Inc. 1. Color: Standard and custom range as manufactured by Tile Tech Pavers Inc. 2. Size: Nominal 20"x20", 16"x16", 12"x12", 12"x24", 16"x24" or Custom Sizes 3.

GUIDE SPECIFICATIONS FOR THE CONSTRUCTION OF …

(80mm) thick pavers are specified, their compressive strength test results per ASTM C140 should be adjusted by multiplying by 1.18 to equate the results to that from 2 3/8 in. (60mm) thick pavers. 2.02 PRODUCT SUBSTITUTIONS A. Substitutions: No substitutions permitted. 2.03 BEDDING AND JOINT SAND A. Provide bedding and joint sand as follows: 1.

US-pavers on mortar bed - EP Henry

Note: If 3 1/8 in. (80 mm) thick pavers are specified, their compressive strength test results per ASTM C 140 should be adjusted by multiplying by 1.18 to equate the results to that from 2 …

Compressive Strength Testing of Concrete Paving Units ...

Jul 01, 2014· Regardless of size or configuration, these units are required to have a minimum average compressive strength of 55 MPa (8000 psi). This strength was originally established when ASTM C936 was first approved in 1982 based on concrete paving units having a thickness of 60 mm (2.36 in.) and a thickness/width aspect ratio of approximately 0.6.

Section 8 SECTION 8: Selection and Installation of ...

Concrete Paver Standards There are two paver standards in North America, one for Canada and one for the U.S. The Canadian standard is published by the Canadian Standards Association (CSA). It is called CSA-A231.2 Precast Concrete Pavers. The standard requires that units have an average minimum compressive strength of 7,200 psi (50 MPa) based

Compressive Strength of Concrete & Concrete Cubes | What ...

Jul 07, 2016· As per Indian code definition. "The compressive strength of concrete is given in terms of the characteristic compressive strength of 150 mm size cubes tested at 28 days (fck). The characteristic strength is defined as the strength of the concrete below which not more than 5% of the test results are expected to fall.".

Paver Thickness - How Thick Are Concrete Pavers ...

Thickness of concrete pavers varies according to the application: Pedestrian areas, driveways, and areas subject to limited vehicular use are paved with units 2 3/8" thick. Streets and industrial pavements should be paved with units 3 1/8" thick. Thin concrete pavers are about 1 1/4" and are applied to existing concrete slabs; Paver Specifications

Paving Systems Using Clay Pavers in a Mortar Setting Bed

Dec 14, 2016· between pavers are prone to early failure and are not recommended Base • Use a plain or reinforced concrete slab; minimum thickness of 4 in. (102 mm); minimum compressive strength of 4000 psi (27.6 MPa) • For exterior applications, use concrete with a minimum air content of 6 percent for increased durability

Specifications for 60mm thick Interlocking Concrete Paving ...

Specifications for 60 mm thick Interlocking Concrete Paving Blocks with ISI mark (IS 15658:2006) Supply of High Strength high finish Interlocking Concrete paving blocks with ISI mark (IS 15658:2006) of VYARA make, with - wear resistant aggregates colour coordinated aggregates in face mix.

Concrete Grid Pavers - Tech Spec 8 - CastleLite Block

in. long by 24 in. wide (610 mm by 610 mm) and a minimum nominal thickness of 3 1/8 in. (80 mm). The minimum required thickness of the webs between the openings is 1 in. (25 mm). Dimensional tolerances should not differ from approved samples more than 1/8 in. (3.2 mm) for length, width, and height. The minimum compressive strength of the concrete

Structural Design of Interlocking Concrete Paving Block ...

Dec 20, 2016· It is the one of the important load- spreading component of the pavement. However advantages of interlocking concrete pavement have not fully extended in India. This project deals with the advantage of interlock system, stone shape, thickness, compressive strength, size, and pattern and cost analysis on the overall pavement performance.

Tech Spec 2 - Western PA Concrete Products Producer

aggregate base, bedding sand and concrete pavers. This pave - ment structure is commonly used for pedestrian and vehicular applications. Pedestrian areas, driveways, and areas subject to limited vehicular use are paved with units 2 3/8 in. (60 mm) thick. Streets and industrial pavements should be paved with units at least 3 1/8 in. (80 mm) thick.

COMPRESSIVE STRENGTH TESTING OF PAVER

Type of unit: Paver Capping material: Plywood Orientation of the unit: NA Height to thickness Ratio / Aspect ratio factor (K a): 0.29 / 0 Moisture content: NA Results: Specimen Number: Width (mm) Height (mm) Thickness (mm) Maximum Load kN Unconfined compressive strength (MPa) 1 370100.1 100.1 28.8 37 2 100.0 100.0 29.0 340 34 3 100.2 370100.3 ...

ASTM Designation: C 936-82 (Reapproved ... - Cambridge …

9 1 / 2 in. (240 mm) in length or 5 1 / 2 in. (140 mm) in thickness. 1.2 Concrete units covered by this specification may be made from lightweight or normal weight aggregates or mixed lightweight and normal weight aggregates. 1.3 When particular features are desired, such as weight classification, higher compressive strength,

Flexural and Compressive Strength of Concrete Tiles with ...

The compressive strength of concrete, one of the most important and useful properties, is indicated by the unit stress required to cause the failure of a specimen, he clarified. ... It is indicated that pavers (tiles) should have a minimum thickness of 38 mm, and a standard thickness of 60 mm for light traffic and 80 mm for heavy traffic ...

Specifications for 80 mm thick Interlocking Concrete ...

2. Compressive strength Average not less than 450 Kg/cm2 3. Average wear in Thickness- Abrasion Average wear not more than 2mm 4. Tolerance in size (length + breadth) ± 2mm 5. Thickness of wearing layer Not less than 5mm 6. Tolerance in Thickness of block ± 5mm 7. Colours UV Light resistant fast colours from Lanxess only to be used.

Holland Stone Series - Pavestone

Note: Requires modifying the ASTM C 140 - Paver Annex A4 - "The test specimen shall be 60 ± 3 mm thick and, if necessary, cut to a specimen size having a Height/Thickness (width) [H/T] aspect ratio of 0.6 ± 0.1 INSTALLATION 1. Excavate unsuitable, unstable or unconsolidated subgrade material and compact the area which has been cleared.

Paver Specifications | Sunny Brook | Large-Scale Paver ...

The result is a premium paver offering a minimum compressive strength of 8,500 pounds per square inch (psi) (58,605 kPa), a density of 150 pounds per cubic foot and a water absorption rate less than five percent. With our precision engineering, we can manufacture our pavers to meet any architectural or engineering specification.

Compressive strength in concrete paving blocks. Results ...

Compressive strength in concrete paving blocks. Results leading to validate the test in half-unit specimens P. Vila, M. N. Pereyra, Á. Gutiérrez 249 the units can be cut) (UNIT 787, 1978). The cross section of the blocks produced in Uruguay are not bigger than that value, so the compressive strength tests are always done in whole units.

Influence of Bacteria on Compressive Strength of Rubber ...

that the strength of concrete paver block depends measuredly on quality of concrete. Thus an attempt present ... 60 Mm Thick Rubber Mould Paver Block (Is: 456-2000, Irc: Sp: 63-2004) Cement F. A C. A Admixture Water 410 685 1160 7 155 ... Compressive Strength of Rubber Mould Paver Block M30 Grade Mix and Rubber Mould Paver Block